Harting plugs
Harting Han-Snap® series
A Harting connector installed with a Han-Snap® element normally does not have touch protection. The protection against electric shock must be ensured by the type of installation by the user. The consistency of the PE connection must be checked by the user. The PE terminal must be equilateral.
- The Han-Snap® system is ideal for connectors within closed electrical workshops. These may be rooms, cabinets or distributor boxes.
- The Han-Snap® elements are technically high-quality plastic parts with optimum properties for the
- Reduction of material and installation costs;
- Easy, simple installation;
- Prefabrication of Han connectors;
- Fast and stable locking of Han connectors;
- Frequent activation of the locking systems, up to several thousand cycles. - The Han-Snap® elements fit the serial contact inserts and connection distributors of the series (referred to hereinafter as Size B)
- Han D®, 40 and 64-pin
- Han DD®
- Han E®
- Han® EE
- Han® EEE
- Han® ES
- Han Hv E®
- Han® Hv ES
- Han® HsB
- Han-Com® (except Han® K 4/4)
- Han Modular® - When using the Han-Snap® adapter, the serial contact inserts of series (hereinafter referred to as Size A) fit
- Han D®, 15 and 25-pin
- Han A®, 10 and 16-pin - The Han-Snap® elements according to the modular principle. Normally, the plastic components are assembled with the same screws that are already part of the contact insert. If coding is required, accessories such as coding pins, guide pins and bushes can be used.
- On free connectors, the wires or cables can be secured with standard cable ties of a maximum width of 5 mm.
" Han-Snap® latching parts "
- Compact design saves space
- Practical and easy handling
- Reduction of material and assembly costs
| Limiting temperature | -40 ... +125 °C |
| Protection class acc. to IEC 60529 | IP20 |
| Retention force | 200 N without guiding, 300 N with guiding |
| Material (accessories) | Polycarbonate (PC) |
| Colour (accessories) |
RAL 7032 (pebble grey) |
| Material flammability class acc. to UL 94 | V-0 |
|
Standards and approvals |
|
Details
- The contact inserts can be mounted on the components, e.g. the panel mounting and latching parts, with the standard insert mounting screws (tightening torque 0.8 Nm).
- Fixings offer high reliability. No impairment if torque is exceeded slightly.
- Alternatively, Han® coding elements (coding pins, guide pins and bushes) can be used. The identification strip 9 x 20 mm can be fitted in both sides of the latching parts. The identification strip 7 x 20 mm also fits in the slot on the end face of each latching part.
- Up to 2 cable ties with max. 5 mm width can be used on the strain relief element.
Caution! Always fit the strain relief element on the side of the contact insert that is opposite the PE terminal.
Han Snap® plastic panel mountings
- Snap element for sheet metal cut-out
- Compact design saves space
- Practical and easy handling
- Reduction of material and assembly costs
| Limiting temperature | -40 ... +125 °C |
| Retention force | >=250 N in the sheet metal cut-out |
| Material (accessories) | Polycarbonate (PC) |
| Colour (accessories) |
RAL 7032 (pebble grey) |
| Material flammability class acc. to UL 94 | V-0 |
|
Standards and approvals |
|
Details
- The contact inserts and terminal block connectors can be mounted on the components for panel mounting with the standard insert mounting screws (tightening torque 0.8 Nm).
- Fixings offer high reliability.
- No impairment if torque is exceeded slightly.
- Alternatively, Han® coding elements (coding pins, guide pins and bushes) can be used.
- Installation of the connector into the panel opening (sheet metal cut-out) or between 2 parallel mounted rails is possible from the mating or terminal side.
" Han Snap® metal panel mountings "
- Snap element for sheet metal cut-out
- Compact design saves space
- Practical and easy handling
- Reduction of material and assembly costs
| Limiting temperature | -40 ... +125 °C |
| Material (accessories) |
Zinc-die cast |
|
Standards and approvals |
|
Details
- The contact inserts and terminal block connectors can be mounted on the components for panel mounting with the standard insert mounting screws (tightening torque 0.8 Nm).
- Fixings offer high reliability.
- Alternatively, Han® coding elements (coding pins or guide pins and bushes) can be used.
- Installation of the connector into the panel opening (sheet metal cut-out) is from the mating side.
" Han Snap® insert mounting "
- Insert is mounted with carrier element
- The practical solution for mounting a contact insert on the mounting rail
- Tool-free assembly of contact inserts in the Han-Snap® carrier element
- Compact design saves space
| Limiting temperature | -40 ... +125 °C |
| Retention force | >=300 N On rail (tension), >=1.000 N On rail (compression) |
| Material (accessories) | Polycarbonate (PC) |
| Colour (accessories) |
RAL 7032 (pebble grey) |
| Material flammability class acc. to UL 94 | V-0 |
|
Standards and approvals |
|
Details
- The insert mounting locks directly on standard rails 35 x 15 or 35 x 7.5 mm.
- The contact inserts can be assembled on the insert mounting with the standard insert mounting screws (tightening torque 0.8 Nm).
- Fixings offer high reliability.
- No impairment if torque is exceeded slightly.
- Alternatively, Han® coding elements (coding pins or guide pins and bushes) may be used instead of the mounting screws.
- The following identification strips can be optionally fitted in the corresponding slots:
Identification strip 7 x 20 mm or 9 x 20 mm
" Han Snap® insert mounting with carrier element "
- Insert is mounted with carrier element
- The practical solution for mounting a contact insert on the mounting rail
- Tool-free assembly of contact inserts in the Han-Snap® carrier element
- Compact design saves space
| Limiting temperature | -40 ... +125 °C |
| Retention force | >=450 N On rail |
| Material (accessories) | Polycarbonate (PC) |
| Colour (accessories) |
RAL 7032 (pebble grey) |
| Material flammability class acc. to UL 94 | V-0 |
|
Standards and approvals |
|
Details
- The carrier element is the base element for mounting contact inserts transversely on standard rails, for example:
- Top hat rail, 35 x 7.5 or 35 x 15 in accordance with DIN EN 60 715
- C-rail, C 30 in accordance with DIN EN 60 715
- G-rail, G 32 in accordance with DIN EN 60 715 - If exposed to strong vibrations, only use top hat rail 35 x 15. Also recommended when using the large carrier element (greater stability).
- Insert mounting type 6/10 is suitable for contact inserts in sizes 6 B and 10 B.
- Insert mounting type 6/24 is suitable for all contact inserts in sizes 6 B, 10 B, 16 B and 24 B, as well as 16 A with the corresponding adapter.
- The contact inserts can be mounted on the insert mounting with the standard insert mounting screws (tightening torque 0.8 Nm).
- Fixings offer high reliability. No impairment if torque is exceeded slightly.
- Alternatively, Han® coding elements (coding pins or guide pins and bushes) may be used instead of the mounting screws.
- The following identification strips can be optionally fitted in the corresponding slots:
Identification strip 7 x 20 mm or 9 x 20 mm
" Han-Snap® shell housing "
- Ideal for use within closed electrical operating environments
- Cables can be pre-assembled
- Optimisation of material and assembly costs
- Tool-free assembly of contact inserts in the Han Snap® carrier element
| Limiting temperature | -40 ... +125 °C |
| Retention force | >=300 N in locked position |
| Material (accessories) | Polycarbonate (PC) |
| Colour (accessories) |
RAL 7032 (pebble grey) |
| Material flammability class acc. to UL 94 | V-0 |
|
Standards and approvals |
|
Details
A shell housing consists of 2 identical half shells. Each housing has 3 cable entries, 1x on top and one on each side. 2 cable entries can be closed using the supplied blanking plugs. There are rectangular openings near the cable entries for attaching cable ties up to max. 5 mm width. Where the housing shells join, they are held together by the screws from the contact insert.
The half shells can be released using a screwdriver (3.5 x 0.5). Alternatively, Han® coding elements (coding pins or guide pins and bushes) may be used instead of the standard fastening screws. Tightening torque 0.8 Nm.
- Fixings offer high reliability.
- No impairment if torque is exceeded slightly.
- The blanking plugs have slots for identification strips. The following can be fitted as required: Identification strip 7 x 20 mm or 9 x 20 mm Size 16 A with the corresponding adapter.
- The contact inserts can be mounted to the adapters with the standard insert mounting screws. These can then be fixed to the corresponding Han-Snap® elements with the supplied screws.